Investigating the inverse square law Essay

The intensity of the influence at any(prenominal) given radius, r, is the arising strength divided by the area of the sphere. 1 The inverse square uprightness can as well as be applied to gravity, electric fields, light and sound. In relation to electric fields, the electric force in Coulombs natural law follows the inverse square law If gamma rays are a form of electromagnetic beam of light and undergo negligible absorption in air, then the intensity, I, should exchange inversely as the square of the distance between the line and the detector.2 Air acts as an almost transparent medium to ? -rays, and the intensity (rate of energy comer per unit area) of ?-rays emanating from a point source varies inversely as the square of the distance from the source. 3 ?-rays fall into many distinct monoenergetic groups because of their changeable energies which emanate from any particular emitter. The least energetic radiation allow only pass with very thin foils, whereas the most ener getic can penetrate up to several centimetres of lead.4 As ? -rays tend to produce 10-4 times as many ion-pairs per unit length as ? -particles do, measurements are usually carried out victimization a Geiger-Mi ller (G-M) metro. 5 G-M tubings are widely apply for detecting radiation and ionising particles.The anode is kept at a positive say-so and the cathode is earthed. The tube may also have a thin mica end window. 6 When radiation enters the tube, a few electrons and ions are produced in the gas. If the voltage is above the breakdown potential (The minimum reverse voltage to make the diode conduct in reverse)7 of the gas, the number of electrons and ions are greatly multiplied. The electrons are attracted to the anode, and the positive ions move towards the cathode.The current slick in the high resistance resistor (R) produces a pd which is amplified and passed to a counter which registers the passage of an ionising particle or radiation through the tube. 8 The tube cannot be filled with air as the discharge persists for a short time after(prenominal) the radiation is registered. This is due to electrons being emitted from the cathode by the positive ions which come to there. Instead, the tube is filled with argon mixed with a halogen vapour which quenches, reduces the intensity, the discharge quickly, ensuring that the registered radiation does not affect the recording of other ionising particles.When the G-M tube is detecting unity particle, if another enters the tube it allow for not be detected. This is known as dead time the average maximum being approximately 90 microseconds. 9 Because this number is so small, it can justifiably be ignored for this experiment. Background radiation mustiness be taken into account when taking readings from the source. Background radiation primarily comes from cosmic radiation and terrestrial sources. 10 This radiation leave affect the count and must be right. The level of this radiation varies with locati on and must be measured before conducting the experiment.N0e-? t so ? = gradient/ N0e-? t Safety Precautions To operate the utmost safety before, during and after this experiment, some guidelines should be followed fodder and drink should not be consumed whilst in the same room as the source Food items should not be stored in the same room as the source.The source should only be handled with long handled source intervention tongs, and as little as viable Hands should be washed thoroughly after contact with the source If in contact with the source for an extended period, it is recommended that a monitoring badge is worn As the source will radiate in only one direction, it should not be pointed at anyone The source should be locked away in a lead lined box when not in use Open wounds should be covered securely.Protective gloves should be warn when handling potentially contaminated items Errors To reduce the possible errors within the experiment, an optical patio will be used to en sure that the G-M tube and the source are properly aligned throughout, as the source radiates in one direction, the alignment must remain standard. Also, for small distances, specifically the distance d0 which is the distance the source is from the opening of the holder plus the distance of detection from the window in the G-M tube, vernier callipers will be used to hold as much accuracy as possible.Vernier callipers read to fractions of a millimetre, making them much more accurate than other measuring devices. Other distances, such as distance d, can be measured with a metre rule as the distances are larger which decreases the possible error in measuring. There will also be the error of human reaction times from observing the final count and pressing the stopclock. To ensure accuracy, practise using the stop-clock and count switch until reasonably consistent results can be obtained. Preliminary Work To decide on an appropriate voltage to use, the G-M tube and source set-up should b e tested.Place the source approximately 10 cm from the window of the G-M tube and increase the voltage slowly, until the count rate stops ever-changing dramatically. Plot a graph of the count-rate, C, against EHT voltage, V. Record the voltages V1 and V2 between which the rate of counting does not vary too much. If the rate of counting begins to rise after be much the same for a range of voltage do not raise the voltage any higher or the tube may stomach damage. 14 The optimum operating voltage will be halfway between the voltage where the plateau begins and the voltage where it ends.To decide on the range of distances used, the source was moved close to the window of the G-M tube and was moved back slowly until the scaler could count adequately (5 cm). This is the smallest distance that will be used. To find the other extreme, the source was moved back until the count rate fell to a low value, but could still provide adequate results (35 cm).From these preliminary results I have unflinching to time for 10,000 counts at 5 cm from the source, 5000 counts for 10cm from the source, and 1000 for 15 30cm. This is because any higher values will take considerably longer to measure. I will take three readings from each, as radioactive decay is a random process and it would be unlikely for more than three readings to be similar. An average will be calculated from the three values and the reading for the background radiation will be subtracted to find the corrected count rate. Equipment Geiger-Mi ller tube of i lovesome type.Decade scaler with variable EHT supply Sealed cobalt-60 source sealed to prevent contact with the source and to prevent isotropic radiation Long handled source handling tongs to prevent contact with the source Optical bench with source holder to ensure constant alignment Stop-clock, readable to at least deuce decimal places Vernier callipers to measure the distance d0 to a higher level of accuracy Metre rule to measure the distance d Diagr am Where B is the optical bench with source holder, H G is the Geiger-Mi ller tube S is the decade scaler with variable EHT supply.R is the sealed radioactive source, cobalt-60 Cobalt-60 will be used as the gamma source as it is easily produced, by exposing natural cobalt to neutrons in a reactor, and therefore easy to acquire. 15 It also produces ? -rays with energies of 1. 17 MeV and 1. 33 MeV. Method 1. Clamp the G-M tube to one end of the optical bench and attach it to the input socket of the scaler 2. Set the variable EHT voltage on the scaler at a minimum and turn it on, allowing a few minutes for the scaler to warm up 3. Change the variable EHT voltage on the scaler to the value found through preliminary work and set it to count pulses from the G-M tube.4. Start the stopclock and measure the background radiation for an adequate length of time, e. g. 25 minutes, as background radiation is variable 5. Place the holder containing the ? -source at 5. 0 cm from the window of the G -M tube 6. Start the stopclock and stop after 10,000 counts are registered. Record this value and repeat in two ways 7. Move the ? -source to 10. 0 cm from the window of the G-M tube and repeat procedure 5, instead only counting 5000 counts 8. Move the ? -source to 15. 0 cm from the window of the G-M tube and repeat procedure 5, instead counting only 1000 counts 9.Repeat procedure 7 for sets of 5. 0 cm until a distance of 30. 0 cm is reached 10. Tabulate these results and find the average count rate for each distance 11. Evaluate 1/(d + do)2 12. Using the recorded value for background radiation, evaluate the corrected count rate for each distance 13. Plot the graph of corrected count rate against 1/(d + do)2 1 http//hyperphysics. phy-astr. gsu. edu/Hbase/forces/isq. hypertext mark-up language 2 Essential Pre-University natural philosophy Whelan & Hodgson, rogueboy 953 3 Essential Principles of Physics Whelan & Hodgson, page 472 4 Essential Principles of Physics Whelan & Hodg son, page 472.5 Essential Principles of Physics Whelan & Hodgson, page 472 6 http//www. imagesco. com/articles/geiger/03. html 7 http//en. wikipedia. org/wiki/Breakdown_voltage 8 Essential Pre-University Physics Whelan & Hodgson, page 406 9 http//www. imagesco. com/articles/geiger/03. html 10 http//en. wikipedia. org/wiki/Background_radiation 11 Advanced Level Practical Physics M Nelkon & JM Ogborn, page 218 12 A Laboratory Manual of Physics F. Tyler, page 269 13 http//en. wikipedia. org/wiki/Cobalt 14 Advanced Level Practical Physics M Nelkon & JM Ogborn, page 212 15 http//en. wikipedia. org/wiki/Cobalt.Source http//en.wikipedia. org/wiki/Geiger-M%C3%BCller_tube The anode is a central thin wire which is insulated from the surrounding cathode cylinder, which is metal or graphite coated.